previous vectron model number c3310 output frequency range 10 mhz C 160 mhz standard frequencies 10; 25; 26; 39.3216; 52; 56; 61.44;77.76; 104 mhz 122.88; 153.6; 155.52; 160 mhz parameter min typ max units condition input frequency 2 100 mhz 2 ppm signal hcmos hcmos / similar sinewave reference level reference input impedance 0.5 2 4 v pp k ? parameter min typ max units condition output frequency 10 160 mhz signal hcmos @ 15 pf 10 to 90 % @ vs/2 load 15.0 pf rise and fall time 5 ns duty cycle 40 60 % fx-501 frequency controlled crystal oscillator reference frequency base stations test equipment messurement surface mount package refow process compatible low phase noise build in ppl-circuit features typical applications output frequency htttp://www.vectron.com vectron international?267 lowellroad , hudson, new hampshire 03051?tel:+1-88-vectron-1 vectron international gmbh & co. kg ? landstra?e, 74924 neckarbischofsheim, germany ? tel: +49 7268 801 100 fx-501 page: 1/5
parameter min typ max units condition supply voltage [standard] 3.135 3.3 3.465 vdc current consumption 50 ma steady state @ +25c & 3.3vdc parameter min typ max units condition phase noise 3 -90 dbc/hz 10 hz @ 122,88 mhz -110 dbc/hz 100 hz hcmos -131 dbc/hz 1 khz -148 dbc/hz 10 khz -156 dbc/hz 100 khz -157 dbc/hz 1 mhz jitter 0.77 ps rms @ 10hz .. 150khz weight 9 g processing & packing handling & processing note operating temperature range -20 +70 c operable temperature range -30 +85 c storage temperature range -55 +125 c 10 mhz; hcmos output 122,88mhz; hcmos output frequency range [hz] jitter [ps rms] frequency range [hz] jitter [ps rms] 10hz to 100khz 0.708ps 10hz to 150khz 0.755ps supply voltage (vs) additional parameters htttp://www.vectron.com vectron international?267 lowellroad , hudson, new hampshire 03051?tel:+1-88-vectron-1 vectron international gmbh & co. kg ? landstra?e, 74924 neckarbischofsheim, germany ? tel: +49 7268 801 100 fx-501 page: 2/5 typical phase noise and jitter
type g218b input : single ended (hcmos or sinewave) output : single ended hcmos height h pin length l 5.9 na dimensions : mm pin connections description 1 ref. frequency in high stable input frequency for syncronisation 2 vcxo control test output of the control voltage for the vcxo only for modul test or observance 3 gnd ground connection. keep traces physically short and connect immediately to ground plane for best performance 4 rf-out rf syncronised output. 5 lock detector output test output signal for pll lock detected. high signal ? pll in lock low signal ? pll out of lock only for modul test or observance 6 vs power supply pin marking fx-501 frequency ayyww absolute maximum ratings htttp://www.vectron.com vectron international?267 lowellroad , hudson, new hampshire 03051?tel:+1-88-vectron-1 vectron international gmbh & co. kg ? landstra?e, 74924 neckarbischofsheim, germany ? tel: +49 7268 801 100 enclosure fx-501 page: 3/5 parameter min typ max units condition supply voltage (vs) 6.0 v maximum output load @ cmos 40 pf
standard shipping methode htttp://www.vectron.com vectron international?267 lowellroad , hudson, new hampshire 03051?tel:+1-88-vectron-1 vectron international gmbh & co. kg ? landstra?e, 74924 neckarbischofsheim, germany ? tel: +49 7268 801 100 block diagram fx-501 page: 4/5 vs 8 1 5 4 0 8 1 5 4 vcxo pll circuit reference frequency vcxo lock detector vcxo control 0 vcxo vs vs 0 loop filter vs *bei w 24 mm nur untere lochreihe ? by w 24 mm only lower hole line gurtoberseite tape upper side gurtunterseite tape buttom side abwickelrichtung unwinding direction lage im gurt position in tape pin 1 a x p b k production tolerance complying din iec 286-3 enclosure type tape width w [mm] quantity per meter quantity per reel dimension p g218b tbd tbd 850 tbd notes: 1 contact factory for improved stabilities or additional product options. not all options and codes are available at all frequencies. 2 unless otherwise stated all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency control voltage, load, temperature (25c) 3 phase noise degrades with increasing output frequency. 4 subject to technical modifcation. 5 contact factory for availability.
profle feature pb-free assembly/ sn-pb assembly profle feature pb-free assembly/ sn-pb assembly average ramp-up rate (t l to t p ) 3c/second max. time 25c to peak temperature 8 minutes max. preheat -temperature min t smin -temperature min t smax -time (min to max) t s 150c 200c 60-180 seconds time maintainted above -temperature (t l ) -time (t l ) 217c 60-150 seconds t smax to t l -ramp-up rate 3c/second max time maintainted above -temperature (t l ) -time (t l ) 217c 60-150 seconds time within 5c of actual peak temperature (t p ) 20-40 seconds peak temperature (t p ) max 260c ramp-down rate 6c/ second max note: all temperatures refer to topside of the package, measured on the package body surface. smd oscillators must be on the top side of the pcb during the refow process how to order this product: supply voltage code: e: 3,3 v rf output code: a: hcmos height: 1: 5,9 mm temperature range: h: -30...+85c j: -20...+70c htttp://www.vectron.com vectron international?267 lowellroad , hudson, new hampshire 03051?tel:+1-88-vectron-1 vectron international gmbh & co. kg ? landstra?e, 74924 neckarbischofsheim, germany ? tel: +49 7268 801 100 recommanded refow profle use this worksheet to forward the following information to your factory representative: model height - supply voltage code rf output code temperature range - reference frequency - output frequency fx-401 1 - e a j - - fx-501 page: 5/5
|
